|
 amcAccuFlow HP.pdf
amcAccuFlow HP cartridge is a premium sterilizing-grade filter product combining two layers of amcAccupor membrane with thermally bonded polypropylene components to provide a durable filter for aggressive microfiltration applications. Its double layer membrane configuration makes the cartridge ideally suited for final filtration in critical applications, especially those involving fluids at high temperatures.
amcAccuFlow HP cartridge is manufactured under tightly controlled procedures for consistent and reliable performance. During manufacturing, each amcAccuFlow HP cartridge is flushed with proprietary solvents, followed by purified water, and integrity tested to ensure the product quality.
amcAccuFlow HP cartridge is compatible with multiple autoclave and in-line steam sterilization, as well as chemical sanitization methods.
Performance Advantages:
|
* |
Constructed of only two materials, i.e., modified polyethersulfone and polypropylene with no adhesives to ensure lower extractables
|
|
* |
Manufactured under stringent processes to ensure highest level of quality and consistency
|
|
* |
Provides high particle retention to minimize filter change-outs during batch processing
|
|
* |
Maximizes recovery of critical solution components with amcAccupor PES membrane's extensive drug compatibility and low protein binding characteristics
|
|
* |
Offers great resistance to severe sanitizing agents such as hot water, concentrated hydrogen peroxides, and active chloride compounds
|
|
* |
100% integrity tested in production to ensure optimal quality product |
Materials of Construction:
Filter Media: two layers of pleated amcAccupor membrane, i.e., modified polyethersulfone hydrophilic membrane
Support Material: polypropylene
Structure Components: polypropylene
Sealing Technology: thermal Bonding
Nominal Length: 10, 20, 30 and 40 inch (25.4, 50.8, 76.2 and 101.6 cm)
Diameter: 2.7 inches (6.9 cm)
Nominal Pore Size: 0.1 and 0.2 μm
Typical Effective Filtration Area: 5.8 ft2 (0.54 m2) per 10 inch
Maximum Operating Temperature*: 90℃ at 30 psi (2.1 bar)
* Supported adapters are recommended for applications at elevated temperature over 60 ℃
Sterilization/Sanitization Methods:
Chemical: peracetic acid, chlorinated alkaline products, bleach, sulfur dioxide, and hydrogen peroxide at typical sanitization concentrations and temperatures
Autoclave: 121℃ for 30 minutes up to 20 cycles
In-line Steam: 121℃ for 60 minutes at 2 psi (0.14 bar) up to 20 cycles
142℃ for 60 minutes at 2 psi (0.14 bar) up to 10
Maximum Differential Forward Pressure: 60 psi (4.1 bar) at ambient temperature
Maximum Differential Back Pressure:
0.1 μm: 30 psi (2.1 bar) at ambient temperature
0.2 μm: 15 psi (1.0 bar) at ambient temperature
Maximum Continuous Pressure: limited by housing
Recommended Integrity Tests
Minimum Bubble Point:
0.1 μm: 28 psi (2.0 bar) in ethanol
0.2 μm: 49 psi (3.4 bar) in water
Diffusional Flow in Water: for more information, please contact us.
Typical Water Flow Rate:
0.1 μm: 0.2 gpm/psi/10 inch length (1.1 lpm/0.1 bar/25.4 cm length)
0.2 μm: 1.2 gpm/psi/10 inch length (6.6 lpm/0.1 bar/25.4 cm length)
Oxidizable Substances: filtrate meets USP XXII requirements for purified water with <1 L flush after autoclaving
Biosafety and CFR Title 21: all components meet USP Class VI-121℃ Plastics Tests, and are listed as being acceptable for food contact according to the Code of Federal Regulation, Title 21
Endotoxin Level: < 0.25 EU/mL utilizing Limulus Amoebocyte Lysate (LAL) test
Typical Non-Volatile Residue: 50 ppm per 10 inch
Bacterial Retention: for more information, please contact us.
Typical Liquid Flow Rate (10 inch length):
amcAccuFlow HP Water Flow Rate:
Cartridge Ordering Information
|
■ |
Rated Pore Size |
10 |
0.1 μm |
|
|
|
20 |
0.2 μm
|
|
◆ |
Nominal Length |
1 |
10 inch (25.4 cm) |
|
|
|
2 |
20 inch (50.8 cm) |
|
|
|
3 |
30 inch (76.2 cm) |
|
|
|
4 |
40 inch (101.6 cm)
|
|
● |
Cartridge Configuration |
D |
SOE, Flat |
|
|
|
F |
DOE, Gasket/Gasket 10 inch increments |
|
|
|
J |
SOE, -222/Flat/SS* |
|
|
|
K |
SOE, -222/Fin/SS* |
|
|
|
M |
SOE, -222/Flat |
|
|
|
P |
SOE, -222/Fin |
|
|
|
Q |
SOE, -226/Fin |
|
|
|
R |
SOE, -226/Fin/SS* |
|
|
|
V |
SOE, -226/Flat |
|
|
|
W |
SOE, -226/Flat/SS*
|
|
▲ |
Seal Material |
S |
Silicone |
|
|
|
V |
Viton |
|
|
|
E |
Ethylene Propylene |
|
|
|
|
|
* SS indicates stainless steel supported adapter
|
